Detaljeret guide kommer snart
Vi arbejder på en omfattende uddannelsesguide til Voltage Drop Calculator. Kom snart tilbage for trin-for-trin forklaringer, formler, eksempler fra virkeligheden og eksperttips.
A voltage drop calculator determines the loss of electrical voltage that occurs when current flows through the resistance of a conductor. All wires have resistance, and when current flows through that resistance, a voltage drop occurs according to Ohm's Law (V = I × R). This voltage drop reduces the voltage available at the load end of the circuit — a motor at the end of a long run may receive only 110 V instead of 120 V, causing reduced torque, increased current draw, overheating, and premature failure. The NEC recommends (but does not mandate in most cases) a maximum of 3 % voltage drop for branch circuits and 5 % total drop from service entrance to the farthest outlet (NEC 210.19 Informational Note 4 and NEC 215.2 Informational Note 2). Voltage drop is affected by four factors: current (more current = more drop), conductor length (longer = more drop), conductor cross-section (smaller wire = more resistance = more drop), and conductor material (aluminum has ~61 % conductivity of copper, causing more drop for the same size). The formula for single-phase circuits uses round-trip resistance (2 × length for both conductors). For three-phase circuits, the factor is √3 because the three phases partially cancel each other. Voltage drop is especially critical for: long branch circuits (outdoor lighting, garage subpanels, rural structures), 120 V circuits (3 % of 120 V = only 3.6 V), and sensitive equipment (precision instruments, variable frequency drives, LED drivers).
Single-phase VD (V) = 2 × K × I × L / CM where K = 12.9 (copper) or 21.2 (aluminum), L = one-way feet, CM = circular mils Alternate: VD = 2 × I × L × R / 1000 (R in ohms per 1000 ft from AWG table) VD % = VD / V_source × 100
- 1Gather the required input values: K, I, L, CM.
- 2Apply the core formula: Single-phase VD (V) = 2 × K × I × L / CM where K = 12.9 (copper) or 21.2 (aluminum), L = one-way feet, CM = circular mils Alternate: VD = 2 × I × L × R / 1000 (R in ohms per 1000 ft from AWG table) VD % = VD / V_source × 100.
- 3Compute intermediate values such as Single-phase: VD if applicable.
- 4Verify that all units are consistent before combining terms.
- 5Calculate the final result and review it for reasonableness.
- 6Check whether any special cases or boundary conditions apply to your inputs.
- 7Interpret the result in context and compare with reference values if available.
Applying the Voltage Drop Calc formula with these inputs yields: VD = 2 × 12.9 × 12 × 150 / 6,530 = 46,440 / 6,530 = 7.11 V. VD % = 7.11/120 = 5.9 %. Well over 3 % limit! Upgrade to AWG 10 (CM = 10,380): VD = 2 × 12.9 × 12 × 150 / 10,380 = 46,440/10,380 = 4.47 V = 3.7 %. Still over. AWG 8 (CM = 16,510): VD = 46,440/16,510 = 2.81 V = 2.3 %. AWG 8 recommended.. This demonstrates a typical voltage drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Applying the Voltage Drop Calc formula with these inputs yields: AWG 2/0 CM = 133,100. VD = 2 × 12.9 × 100 × 200 / 133,100 = 516,000/133,100 = 3.88 V. VD % = 3.88/240 = 1.6 %. Excellent — well under 3 %.. This demonstrates a typical voltage drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Applying the Voltage Drop Calc formula with these inputs yields: Three-phase VD = √3 × K × I × L / CM = 1.732 × 12.9 × 30 × 300 / 16,510 = 201,275/16,510 = 12.19 V. VD % = 12.19/480 = 2.5 %. Within 3 % limit for this run.. This demonstrates a typical voltage drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Applying the Voltage Drop Calc formula with these inputs yields: Current = 100W / 12V = 8.33 A. AWG 16 CM = 2,583. VD = 2 × 12.9 × 8.33 × 50 / 2,583 = 10,746/2,583 = 4.16 V. VD % = 4.16/12 = 34.7 %! Disastrous — lights will be dim. For 12 V systems, VD must be kept under 1–2 V (8–17 %). Use AWG 10 or run multiple shorter homerun branches from the transformer.. This demonstrates a typical voltage drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Long residential branch circuit design, representing an important application area for the Voltage Drop Calc in professional and analytical contexts where accurate voltage drop calculations directly support informed decision-making, strategic planning, and performance optimization
Subpanel feeder sizing, representing an important application area for the Voltage Drop Calc in professional and analytical contexts where accurate voltage drop calculations directly support informed decision-making, strategic planning, and performance optimization
Outdoor and landscape lighting, representing an important application area for the Voltage Drop Calc in professional and analytical contexts where accurate voltage drop calculations directly support informed decision-making, strategic planning, and performance optimization
Motor circuit design for long factory runs, representing an important application area for the Voltage Drop Calc in professional and analytical contexts where accurate voltage drop calculations directly support informed decision-making, strategic planning, and performance optimization
Solar PV DC wiring (string to combiner to inverter), representing an important application area for the Voltage Drop Calc in professional and analytical contexts where accurate voltage drop calculations directly support informed decision-making, strategic planning, and performance optimization
In the Voltage Drop Calc, this scenario requires additional caution when interpreting voltage drop results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when voltage drop calculations fall into non-standard territory.
In the Voltage Drop Calc, this scenario requires additional caution when interpreting voltage drop results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when voltage drop calculations fall into non-standard territory.
In the Voltage Drop Calc, this scenario requires additional caution when interpreting voltage drop results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when voltage drop calculations fall into non-standard territory.
| AWG | Circular Mils | Cu Resistance (Ω/kft) | Al Resistance (Ω/kft) |
|---|---|---|---|
| 14 | 4,110 | 3.07 | 5.06 |
| 12 | 6,530 | 1.93 | 3.18 |
| 10 | 10,380 | 1.21 | 1.99 |
| 8 | 16,510 | 0.764 | 1.26 |
| 6 | 26,240 | 0.491 | 0.808 |
| 4 | 41,740 | 0.308 | 0.508 |
| 2 | 66,360 | 0.194 | 0.319 |
| 1/0 | 105,600 | 0.122 | 0.201 |
| 2/0 | 133,100 | 0.0967 | 0.159 |
| 4/0 | 211,600 | 0.0608 | 0.100 |
Is 3 % voltage drop a code requirement or recommendation?
NEC 210.19 and 215.2 state voltage drop guidance as 'informational notes' — technically recommendations, not enforceable code. However, many AHJs (Authorities Having Jurisdiction) enforce it, and equipment manufacturers may void warranties if voltage drop exceeds 5 %. Always design to meet the 3 %/5 % recommendation. This is particularly important in the context of voltage drop calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise voltage drop calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
Does voltage drop change if the actual load is less than the circuit capacity?
Yes — voltage drop is proportional to actual current draw, not breaker or wire capacity. A 20 A circuit loaded to only 10 A has half the voltage drop of the same circuit at 20 A. This is why voltage drop is calculated using the expected actual load current, not the maximum breaker rating.
What happens to energy lost to voltage drop?
The energy is converted to heat in the conductor — this is resistive loss (I²R heating). In large power systems, even 2–3 % voltage drop represents significant energy waste. A 100 A circuit with 5 V drop dissipates 500 W (I × VD = 100 × 5) in conductor heat continuously — wasteful and adds to cooling loads.
How do I calculate voltage drop for aluminum wire?
Use K = 21.2 instead of 12.9 in the circular mils formula, or use aluminum's resistance values from NEC Chapter 9 Table 9. Aluminum has 61 % the conductivity of copper — the same AWG aluminum wire has 64 % more voltage drop than copper for the same current and length. Aluminum wiring is typically sized 2 AWG larger than copper equivalent.
Does conduit material (steel vs. PVC) affect voltage drop?
Steel conduit (EMT, RMC) can slightly increase effective impedance of conductors due to inductive effects, especially at high currents. NEC Chapter 9 Table 9 provides separate impedance values for steel and PVC conduit. For most practical purposes, the difference is small (< 5 % increase for steel vs. PVC in typical residential/commercial applications).
What is the voltage drop for a 12 V or 24 V DC system?
Low-voltage DC systems (automotive, RV, marine, solar) are extremely sensitive to voltage drop — 1 V drop on a 12 V system is 8.3 %, while 1 V on 120 V is only 0.8 %. For 12 V systems, target < 3 % VD = 0.36 V maximum. This typically requires much larger wire than you'd expect from ampacity alone.
How do I determine one-way circuit length?
Measure the distance from the panel (or source) to the load through the actual wire path — not straight-line distance. Include rises over walls, runs through conduit overhead, etc. Use the actual wire routing length, then apply the 2× factor for round-trip (both conductors) in the formula. This is particularly important in the context of voltage drop calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise voltage drop calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
Pro Tip
For long runs where voltage drop is borderline, increasing one AWG size typically reduces voltage drop by about 20 % (since resistance decreases proportionally to CM, which increases about 26 % per AWG step). Check both the 3 % branch and 5 % total limits from the service entrance.
Vidste du?
High-voltage power transmission lines run at 115,000 to 765,000 volts specifically to minimize current (I = P/V) and thus minimize I²R heating and voltage drop losses. Transmitting 1 MW at 765 kV requires only 1.3 A vs. 8,333 A at 120 V — wire size and losses differ by factors of thousands.