A grease trap (also called a grease interceptor) calculator determines the required size of a grease separation device for commercial food service operations — restaurants, cafeterias, hospitals, and any facility with commercial kitchen wastewater. Grease traps prevent fats, oils, and grease (FOG) from entering the municipal sewer system where they can cause pipe blockages, sewage overflows, and sewer gas problems. The FOG settles and floats in the grease trap as wastewater passes through, allowing relatively clean water to continue to the drain. Grease traps are sized based on the peak flow rate through the fixture drains connected to the trap, expressed in gallons per minute. The PDI (Plumbing and Drainage Institute) Standard G-101 defines the sizing method: trap capacity (gallons) = peak flow rate (GPM) × 2, plus adjustments for detergent use and water temperature. For large commercial applications, pretreatment interceptors (grease interceptors, which are larger underground units) are sized differently using EPA and local pretreatment authority regulations based on daily gallons generated, retention time, and FOG loading. Many municipalities have fats, oils, and grease (FOG) programs that mandate grease interceptors and regular pumping for food service establishments — typically every 30–90 days.
Trap size (gallons) = Peak flow rate (GPM) × Grease retention time (typically 2 minutes) Peak flow (GPM) = Σ fixture flow rates × usage factor Interceptor sizing: Volume = Design flow × Hydraulic retention time
- 1Gather the required input values: Q_peak, V_trap, GPD, HRT.
- 2Apply the core formula: Trap size (gallons) = Peak flow rate (GPM) × Grease retention time (typically 2 minutes) Peak flow (GPM) = Σ fixture flow rates × usage factor Interceptor sizing: Volume = Design flow × Hydraulic retention time.
- 3Compute intermediate values such as Trap size (gallons) if applicable.
- 4Verify that all units are consistent before combining terms.
- 5Calculate the final result and review it for reasonableness.
- 6Check whether any special cases or boundary conditions apply to your inputs.
- 7Interpret the result in context and compare with reference values if available.
Electrical engineers in power distribution companies use Grease Trap Calc to size conductors, calculate voltage drop across long cable runs, and verify that circuit breaker ratings provide adequate protection against fault currents in residential, commercial, and industrial installations.
Electronics design engineers apply Grease Trap Calc during printed circuit board layout to determine trace widths for required current capacity, calculate impedance matching for high-speed signal traces, and verify thermal dissipation in surface-mount components under worst-case operating conditions.
Maintenance technicians in manufacturing plants use Grease Trap Calc to troubleshoot motor control circuits, verify transformer tap settings, and calculate expected current draws when commissioning variable frequency drives and programmable logic controller systems.
Renewable energy system designers rely on Grease Trap Calc to size solar panel arrays, calculate battery bank capacity for off-grid installations, and determine inverter ratings that match the expected peak and continuous load demands of residential and commercial photovoltaic systems.
Open circuit or infinite resistance
In practice, this edge case requires careful consideration because standard assumptions may not hold. When encountering this scenario in grease trap calculator calculations, practitioners should verify boundary conditions, check for division-by-zero risks, and consider whether the model's assumptions remain valid under these extreme conditions.
Short circuit condition
In practice, this edge case requires careful consideration because standard assumptions may not hold. When encountering this scenario in grease trap calculator calculations, practitioners should verify boundary conditions, check for division-by-zero risks, and consider whether the model's assumptions remain valid under these extreme conditions.
Reactive component dominance
In practice, this edge case requires careful consideration because standard assumptions may not hold. When encountering this scenario in grease trap calculator calculations, practitioners should verify boundary conditions, check for division-by-zero risks, and consider whether the model's assumptions remain valid under these extreme conditions.
| Fixture | Peak Flow (GPM) | Minimum Trap Size | Frequency |
|---|---|---|---|
| Single 2-comp sink | 10 GPM | 25 gallons | Monthly |
| 2-comp + 3-comp sinks | 24 GPM | 50 gallons | Bi-weekly |
| Full kitchen (< 50 seats) | 30–50 GPM | 70–100 gallons | Weekly–Monthly |
| Large restaurant (> 100 seats) | 75+ GPM | 750–1,500 gal interceptor | Every 30–60 days |
| Hospital cafeteria | 50–100 GPM | 1,000–2,500 gal interceptor | Every 60–90 days |
What is the difference between a grease trap and a grease interceptor?
Grease trap: small unit (25–100 gallons) installed inside the kitchen, usually under a sink, handling flow from one or a few fixtures. Treated as plumbing fixtures. Grease interceptor: large unit (500–5,000+ gallons) installed underground outside the building, handling all kitchen wastewater. Treated as pretreatment equipment regulated by the local pretreatment authority.
How often should a grease trap be cleaned?
Small grease traps: weekly to monthly for high-volume restaurants; monthly for moderate operations. Rule: pump when grease/solid layer reaches 25 % of trap volume. Large interceptors: every 30–90 days per local FOG ordinance. Neglected traps stop separating FOG and become 'flow-through' — all grease enters the sewer. Pumping logs must be maintained and inspectable.
Do residential kitchens need grease traps?
No — grease traps are required only for commercial food service establishments, not residential kitchens. However, even residential drains benefit from best practices: collect cooking grease in containers for disposal (not down drain), run hot water while pouring liquid fats (though the grease re-solidifies in the pipe within seconds of cooling).
What is a FOG (Fats, Oils, Grease) program?
Many municipalities operate FOG programs requiring food service establishments to: install and maintain properly sized grease interceptors; pump interceptors on a schedule; maintain pumping logs for inspection; submit FOG reports annually. Violations result in fines or permit revocation. The Clean Water Act gives municipalities authority to regulate FOG discharges that interfere with sewer operations.
Can enzyme or biological treatments replace grease trap pumping?
No — enzyme and bacteria products are not a substitute for mechanical grease trap pumping. They may reduce grease accumulation slightly, but do not eliminate the need for regular pumping. Many FOG programs explicitly prohibit enzyme products that liquefy FOG and allow it to flow past the trap into the sewer system in fluid form. Use only to supplement regular pumping.
What size grease trap is required by code?
IPC Table 1003.3.4.1 provides minimum sizes based on fixture flow rates. Two-compartment sink (minimum 10 GPM each): 50-gallon trap. Three-compartment sink (14 GPM each): 70–100 gallon trap. Most jurisdictions set a minimum of 20 gallons for any commercial kitchen trap. Consult local plumbing inspectors — requirements vary significantly by jurisdiction.
Does dishwasher wastewater need to go through a grease trap?
Typically yes — dishwasher water contains FOG from food residue. However, some codes exempt dishwashers operating at 180°F sanitizing rinse (because FOG is liquid at that temperature and may not be effectively captured). Check local requirements. Heat recovery units on high-temp dishwashers can reduce drain temperature to below 140°F, improving grease capture.
Pro Tip
Develop a written grease trap maintenance log from day one — record pumping dates, volume removed, and service company. This log demonstrates FOG compliance during health department and pretreatment authority inspections and can prevent regulatory fines that dwarf the cost of regular maintenance.
Did you know?
New York City's sewer system receives approximately 18 million pounds of fats, oils, and grease annually — enough to fill over 1,000 average-sized swimming pools. FOG buildup causes about 25,000 sewer overflows per year nationwide, releasing raw sewage into waterways and onto streets. This is why FOG programs and grease trap regulations are increasingly strictly enforced.