Guide détaillé à venir
Nous préparons un guide éducatif complet pour le Circuit Breaker Sizing Calculator. Revenez bientôt pour des explications étape par étape, des formules, des exemples concrets et des conseils d'experts.
A circuit breaker calculator determines the correct breaker amperage rating for electrical circuits based on the connected load, conductor ampacity, and NEC code requirements. Circuit breakers serve two purposes: protecting conductors from overheating (by tripping at rated amperage) and providing a disconnect means for circuit maintenance. The breaker rating must match the wire gauge ampacity — a 20 A breaker requires minimum AWG 12 copper wire, a 15 A breaker requires minimum AWG 14 copper. Breakers must also be sized for the specific type of load: continuous loads (operating 3+ hours) must have a breaker rated at 125 % of the load current; motor loads require breakers sized at 175–250 % of full-load current (motors draw high starting current). Modern NEC requirements also specify breaker type for specific applications: AFCI (Arc Fault Circuit Interrupter) breakers are required for bedroom, living room, and most living area circuits (NEC 210.12); GFCI (Ground Fault Circuit Interrupter) protection is required for outdoor, bathroom, kitchen countertop, garage, crawlspace, and unfinished basement circuits (NEC 210.8). Dual-function AFCI/GFCI breakers combine both protections. Commercial applications require breakers rated for their specific panel (same brand/frame usually), with appropriate interrupting capacity (AIC — ampere interrupting capacity) for the available fault current at the panel location.
Breaker Size = Max(Wire Ampacity, 125 % × Continuous Load Current) Motor breaker: 175–250 % × FLA (Full Load Amperes) Standard sizes: 15, 20, 30, 40, 50, 60, 70, 80, 90, 100 A
- 1Gather the required input values: I_load, I_cont, A_wire, FLA.
- 2Apply the core formula: Breaker Size = Max(Wire Ampacity, 125 % × Continuous Load Current) Motor breaker: 175–250 % × FLA (Full Load Amperes) Standard sizes: 15, 20, 30, 40, 50, 60, 70, 80, 90, 100 A.
- 3Compute intermediate values such as Continuous load breaker if applicable.
- 4Verify that all units are consistent before combining terms.
- 5Calculate the final result and review it for reasonableness.
- 6Check whether any special cases or boundary conditions apply to your inputs.
- 7Interpret the result in context and compare with reference values if available.
This example demonstrates circuit breaker calc by computing NEC 210.52(B) requires two 20 A small appliance circuits in kitchen. AWG 12 ampacity = 20 A. Breaker = 20 A, GFCI type (or standard breaker with GFCI receptacles). Each circuit protects separate sections of countertop.. Kitchen countertop GFCI circuit illustrates a typical scenario where the calculator produces a practically useful result from the given inputs.
This example demonstrates circuit breaker calc by computing Continuous load rule: breaker = 32 A × 125 % = 40 A. Use 50 A breaker (next standard size). Wire: AWG 8 copper (50 A ampacity). This follows NEC 625.42 for EVSE circuits. 50 A breaker + AWG 8 is correct.. EV charger EVSE circuit sizing illustrates a typical scenario where the calculator produces a practically useful result from the given inputs.
This example demonstrates circuit breaker calc by computing Motor breaker max = 250 % × 17 A = 42.5 A → use 40 A (next standard size ≤ 250 % of FLA). Wire: 125 % × 17 = 21.25 A → AWG 12 (20 A insufficient, use AWG 10). Overload protection (thermal overload relay) sized at 115–125 % of FLA = 19.55–21.25 A.. 3-HP motor circuit breaker illustrates a typical scenario where the calculator produces a practically useful result from the given inputs.
This example demonstrates circuit breaker calc by computing NEC 210.12: AFCI protection required for bedroom circuits. Options: (1) AFCI breaker (preferred — protects entire circuit); (2) AFCI receptacle at first outlet. Standard 15 A AFCI breaker protects AWG 14 wire (15 A ampacity). Cost premium for AFCI breaker: $35–$55 vs. $5–$8 for standard breaker.. Bedroom circuit AFCI requirement illustrates a typical scenario where the calculator produces a practically useful result from the given inputs.
Residential panel wiring — This application is commonly used by professionals who need precise quantitative analysis to support decision-making, budgeting, and strategic planning in their respective fields, enabling practitioners to make well-informed quantitative decisions based on validated computational methods and industry-standard approaches
EV charger installation — Industry practitioners rely on this calculation to benchmark performance, compare alternatives, and ensure compliance with established standards and regulatory requirements, helping analysts produce accurate results that support strategic planning, resource allocation, and performance benchmarking across organizations
Commercial panel design — Academic researchers and students use this computation to validate theoretical models, complete coursework assignments, and develop deeper understanding of the underlying mathematical principles, allowing professionals to quantify outcomes systematically and compare scenarios using reliable mathematical frameworks and established formulas
Motor control circuits — Financial analysts and planners incorporate this calculation into their workflow to produce accurate forecasts, evaluate risk scenarios, and present data-driven recommendations to stakeholders, supporting data-driven evaluation processes where numerical precision is essential for compliance, reporting, and optimization objectives
Solar PV system interconnection — This application is commonly used by professionals who need precise quantitative analysis to support decision-making, budgeting, and strategic planning in their respective fields, which requires precise quantitative analysis to support evidence-based decisions, strategic resource allocation, and performance optimization across diverse organizational contexts and professional disciplines
{'case': 'Main breaker sizing', 'note': 'Main breaker must be sized for 100 % of load (not 125 % continuous) per NEC 230.90. Standard residential service: 200 A main, 100 A for small homes, 400 A for large homes with EV + heat pump + high loads.'} When encountering this scenario in circuit breaker calc calculations, users should verify that their input values fall within the expected range for the formula to produce meaningful results. Out-of-range inputs can lead to mathematically valid but practically meaningless outputs that do not reflect real-world conditions.
{'case': 'Solar inverter interconnection', 'note': 'NEC 705.12 limits the sum of inverter output breaker + main breaker to 120 % of panel busbar rating. A 200 A bus allows max 40 A inverter output breaker with 200 A main. Larger solar requires supply-side connection or panel upgrade.'} This edge case frequently arises in professional applications of circuit breaker calc where boundary conditions or extreme values are involved. Practitioners should document when this situation occurs and consider whether alternative calculation methods or adjustment factors are more appropriate for their specific use case.
Sizing follows same rules but three-phase load calculations use: I = kW / (√3 × kV × PF) for balanced loads.'} In the context of circuit breaker calc, this special case requires careful interpretation because standard assumptions may not hold. Users should cross-reference results with domain expertise and consider consulting additional references or tools to validate the output under these atypical conditions.
| Circuit Type | Breaker Size | Wire (Cu) | NEC Reference |
|---|---|---|---|
| General lighting/outlets | 15 A | AWG 14 | 210.23 |
| Kitchen/bath small appliance | 20 A GFCI | AWG 12 | 210.52 |
| Clothes dryer | 30 A | AWG 10 | 210.52(B)(1) |
| Kitchen range | 50 A | AWG 6 | 210.52(C)(1) |
| EV charger 32 A continuous | 50 A | AWG 8 | 625.42 |
| Water heater (4500 W, 240 V) | 25 A | AWG 10 | 422.11(E) |
| A/C (3-ton, 240 V) | 40–60 A* | AWG 8–6 | 440.22 |
| Bedroom circuit (AFCI req.) | 15–20 A AFCI | AWG 14–12 | 210.12 |
What is the difference between AFCI, GFCI, and standard breakers?
Standard breakers protect against overload and short circuit. GFCI (Ground Fault CI) protects people — trips at 5 mA ground fault current, preventing electrocution. AFCI (Arc Fault CI) protects against arcing faults in wiring — the leading cause of electrical fires. Dual-function AFCI/GFCI breakers provide both protections and are required in many locations by recent NEC editions.
Can I use a breaker larger than the wire ampacity?
No — the breaker must never exceed the conductor ampacity. The breaker's job is to protect the wire. If you install a 30 A breaker on AWG 14 wire (15 A ampacity), the wire will overheat and potentially start a fire before the breaker trips. Always match breaker to wire, not to load.
What does AIC rating mean on a breaker?
AIC (Ampere Interrupting Capacity) is the maximum fault current the breaker can safely interrupt without exploding or damaging the panel. Residential main panels typically need 10,000 AIC minimum. Commercial panels near utility transformers may need 22,000–65,000 AIC. Match the breaker's AIC to the available fault current at the panel location.
What are standard breaker sizes?
Standard residential: 15, 20, 30, 40, 50, 60, 100 A. Commercial adds: 70, 80, 90, 110, 125, 150, 175, 200 A. Always round UP to the next standard size when calculation gives a non-standard value (e.g., 42.5 A → 50 A) — unless that would exceed the wire ampacity, in which case you must also upsize the wire.
What is a tandem or double-stuff breaker?
A tandem breaker fits two 120 V circuits in one panel slot. NEC and panel manufacturers limit how many tandems a panel can accept (marked on the panel door as 'X spaces, Y circuits'). Tandems should only be used in panels rated for them — using them in non-rated panels is a code violation.
Why do motor circuits need larger breakers than their running current suggests?
Motors draw 6–8× their full load current during starting (inrush current). Standard breakers have a time-delay characteristic that tolerates brief overloads — but must still be sized at 175–250 % of FLA to ride through motor start without nuisance tripping. A separate overload relay (thermal or electronic) protects the motor from sustained overloads.
Do AFCI breakers work with aluminum wiring?
Some AFCI breakers are rated for use with aluminum wiring connections at the breaker terminal, but standard arc-fault protection in older homes with aluminum branch wiring requires careful evaluation. Most aluminum wiring concerns relate to receptacle connections, not the breaker itself. Consult a licensed electrician for aluminum wiring remediation. This is an important consideration when working with circuit breaker calc calculations in practical applications.
Conseil Pro
Label every breaker clearly when installed — 'Kitchen Countertop North', 'Bedroom 1 Outlets', 'EV Charger Garage'. A properly labeled panel takes 5 minutes to complete and saves hours of tracing circuits later during troubleshooting or remodeling.
Le saviez-vous?
Thomas Edison invented the first fusible protection device (a forerunner of circuit breakers) in 1879. The modern thermal-magnetic circuit breaker was developed in the 1920s–1930s. Today, approximately 200 million circuit breakers are manufactured annually in the US alone.