Guide détaillé à venir
Nous préparons un guide éducatif complet pour le Generator Sizing Calculator. Revenez bientôt pour des explications étape par étape, des formules, des exemples concrets et des conseils d'experts.
A generator sizing calculator determines the minimum generator capacity (in watts or kilowatts) needed to power a specific set of loads, whether for emergency backup, off-grid living, or portable construction power. Generators are rated in two ways: running watts (continuous rated output) and starting watts (surge capacity for 5–10 seconds to handle motor startup current). Electric motors can draw 3–6× their running current during startup — an air conditioner rated 1,500 running watts may require 4,500 starting watts. If a generator cannot supply starting wattage, it will stall or trip its overload protection. Generator sizing follows a three-step process: (1) list all loads with both running and starting watts; (2) identify the highest-starting-watt item (only one major motor starts at a time); (3) total running watts of all simultaneous loads plus the starting watt surge for the largest motor. Fuel consumption scales roughly proportionally to load — a generator operating at 50 % load uses approximately 60–65 % of its full-load fuel consumption rate (generators are less efficient at very low loads). Standby generators for whole-home backup are sized differently from portable generators: a standby propane or natural gas unit must handle the peak load of the home including HVAC, and the automatic transfer switch (ATS) ensures seamless cutover within seconds of utility outage.
Generator Size (W) = Total Running Watts + Largest Motor Starting Watts Fuel Consumption (gal/hr) ≈ (kW × load factor) / 10 (approximate for gasoline generators) Runtime (hrs) = Tank capacity (gal) / Fuel consumption rate (gal/hr)
- 1Gather the required input values: W_run, W_start, W_total_run, W_gen.
- 2Apply the core formula: Generator Size (W) = Total Running Watts + Largest Motor Starting Watts Fuel Consumption (gal/hr) ≈ (kW × load factor) / 10 (approximate for gasoline generators) Runtime (hrs) = Tank capacity (gal) / Fuel consumption rate (gal/hr).
- 3Compute intermediate values such as Required generator kVA if applicable.
- 4Verify that all units are consistent before combining terms.
- 5Calculate the final result and review it for reasonableness.
- 6Check whether any special cases or boundary conditions apply to your inputs.
- 7Interpret the result in context and compare with reference values if available.
Electrical engineers in power distribution companies use Generator Sizing Calc to size conductors, calculate voltage drop across long cable runs, and verify that circuit breaker ratings provide adequate protection against fault currents in residential, commercial, and industrial installations.
Electronics design engineers apply Generator Sizing Calc during printed circuit board layout to determine trace widths for required current capacity, calculate impedance matching for high-speed signal traces, and verify thermal dissipation in surface-mount components under worst-case operating conditions.
Maintenance technicians in manufacturing plants use Generator Sizing Calc to troubleshoot motor control circuits, verify transformer tap settings, and calculate expected current draws when commissioning variable frequency drives and programmable logic controller systems.
Renewable energy system designers rely on Generator Sizing Calc to size solar panel arrays, calculate battery bank capacity for off-grid installations, and determine inverter ratings that match the expected peak and continuous load demands of residential and commercial photovoltaic systems.
Open circuit or infinite resistance
In practice, this edge case requires careful consideration because standard assumptions may not hold. When encountering this scenario in generator sizing calculator calculations, practitioners should verify boundary conditions, check for division-by-zero risks, and consider whether the model's assumptions remain valid under these extreme conditions.
Short circuit condition
In practice, this edge case requires careful consideration because standard assumptions may not hold. When encountering this scenario in generator sizing calculator calculations, practitioners should verify boundary conditions, check for division-by-zero risks, and consider whether the model's assumptions remain valid under these extreme conditions.
Reactive component dominance
In practice, this edge case requires careful consideration because standard assumptions may not hold. When encountering this scenario in generator sizing calculator calculations, practitioners should verify boundary conditions, check for division-by-zero risks, and consider whether the model's assumptions remain valid under these extreme conditions.
| Device | Running Watts | Starting Watts |
|---|---|---|
| Refrigerator/freezer | 150–400 W | 500–1,200 W |
| Window A/C (10,000 BTU) | 1,200 W | 3,600 W |
| Central A/C (3-ton) | 4,500 W | 12,000 W |
| Sump pump (1/2 HP) | 800 W | 2,000 W |
| Well pump (1 HP, 240 V) | 1,500 W | 4,500 W |
| Electric water heater | 4,500 W | 4,500 W (resistive, no surge) |
| Microwave (1,000 W) | 1,000 W | 1,000 W (no surge) |
| TV (50-inch LED) | 150 W | 150 W (no surge) |
| LED lighting (full home) | 200–500 W | 200–500 W |
| CPAP machine | 30–60 W | 30–60 W (no surge) |
What is the difference between running watts and starting watts?
Running watts (also called rated watts) is the continuous power a device consumes in normal operation. Starting watts (surge watts) is the brief power surge needed when a motor starts — typically 2–3× running watts for refrigerators, 3–5× for air conditioners and well pumps. The generator must supply starting watts without stalling.
Can I connect a generator directly to my home's panel?
Never connect a generator directly to an outlet or panel without a transfer switch — this creates 'backfeed' that can electrocute utility workers repairing outage lines. A manual transfer switch or interlock kit disconnects the utility before the generator connects. Automatic transfer switches (ATS) do this automatically and are required for standby generators.
What fuel type is best for home standby generators?
Propane or natural gas is preferred for standby generators — it stores indefinitely (vs. gasoline which degrades in 3–6 months), and natural gas connects directly to utility supply without tank limits. Diesel is best for large commercial generators (reliable, efficient). Gasoline portables are most flexible for short outages. Dual-fuel generators (gas + propane) offer versatility.
How much does a whole-home generator cost?
In the context of Generator Sizing Calc, this depends on the specific inputs, assumptions, and goals of the user. The underlying formula provides a deterministic relationship between inputs and output, but real-world application requires interpreting the result within the broader context of engineering and electrical practice. Professionals typically cross-reference calculator output with industry benchmarks, historical data, and regulatory requirements. For the most reliable results, ensure inputs are sourced from verified data, understand which assumptions the formula makes, and consider running multiple scenarios to bracket the range of likely outcomes.
What size generator do I need to run my central air conditioner?
In the context of Generator Sizing Calc, this depends on the specific inputs, assumptions, and goals of the user. The underlying formula provides a deterministic relationship between inputs and output, but real-world application requires interpreting the result within the broader context of engineering and electrical practice. Professionals typically cross-reference calculator output with industry benchmarks, historical data, and regulatory requirements. For the most reliable results, ensure inputs are sourced from verified data, understand which assumptions the formula makes, and consider running multiple scenarios to bracket the range of likely outcomes.
What is an inverter generator and why is it better for sensitive electronics?
Inverter generators produce clean 'sine wave' power (THD < 3 %) by converting AC to DC then back to AC, whereas conventional generators produce 'modified sine wave' power (THD 5–25 %). Sensitive electronics (laptops, TV, medical equipment) can be damaged or malfunction on high-THD power. Inverter generators are also quieter (50–60 dB vs. 65–75 dB) and more fuel-efficient at partial loads.
How do I store a generator safely?
Store outdoors or in a well-ventilated area — never run indoors or in a garage. Carbon monoxide kills within minutes. Store with fresh fuel and fuel stabilizer, or drain fuel for long-term storage. Run the generator to operating temperature quarterly to maintain engine condition. Check oil level every 8 hours of operation.
Conseil Pro
Add 20–25 % margin to your calculated generator size — this provides headroom for adding loads, handles efficiency degradation as the generator ages, and reduces thermal stress for longer equipment life. A generator running at 75 % of rated load lasts significantly longer than one pegged at 100 %.
Le saviez-vous?
Hurricane Katrina (2005) caused such high demand for generators that warehouse stocks nationwide depleted within days. The US has approximately 12 million portable generators and 500,000 standby generators in service — enough to power a small country.