詳細ガイド 近日公開
Pressure Drop Calculatorの包括的な教育ガイドを準備中です。ステップバイステップの解説、数式、実例、専門家のヒントをお届けしますので、もうしばらくお待ちください。
A pressure drop calculator determines the reduction in fluid pressure that occurs as fluid flows through a pipe, fitting, valve, or heat exchanger. Pressure drop (also called friction loss or head loss) occurs because the fluid must overcome friction from the pipe walls and turbulence within the flow. In plumbing and HVAC systems, pressure drop governs whether adequate pressure reaches all fixtures and equipment. In HVAC hydronic heating/cooling systems, pressure drop determines pump selection — the pump must overcome total system pressure drop at design flow rate. The Darcy-Weisbach equation is the fundamental physics-based model: ΔP = f × (L/D) × (ρ × V² / 2), where f is the Moody friction factor determined by the Reynolds number and relative roughness. For practical water piping at typical flows, empirical Hazen-Williams tables provide quick pressure drop lookup. For HVAC hydronic systems, pressure drop is expressed in feet of head (1 psi = 2.31 feet of water head) or Pascals. Every fitting, valve, and component adds to the total system pressure drop — expressed either as equivalent pipe length or as a resistance coefficient (K-value). The design goal is to balance the system so all circuits have similar pressure drop, enabling the pump to deliver design flow everywhere without excessive throttling at some circuits.
Darcy-Weisbach: ΔP = f × (L/D) × (ρV²/2) [Pa or psi] Head loss: h = f × (L/D) × V²/(2g) [feet of fluid] Fitting loss: ΔP = K × ρV²/2 [K = fitting resistance coefficient] Total head = pipe head + fitting head + elevation head
- 1Gather the required input values: ΔP, f, L/D, ρ.
- 2Apply the core formula: Darcy-Weisbach: ΔP = f × (L/D) × (ρV²/2) [Pa or psi] Head loss: h = f × (L/D) × V²/(2g) [feet of fluid] Fitting loss: ΔP = K × ρV²/2 [K = fitting resistance coefficient] Total head = pipe head + fitting head + elevation head.
- 3Compute intermediate values such as Darcy-Weisbach: h if applicable.
- 4Verify that all units are consistent before combining terms.
- 5Calculate the final result and review it for reasonableness.
- 6Check whether any special cases or boundary conditions apply to your inputs.
- 7Interpret the result in context and compare with reference values if available.
Applying the Pressure Drop Calc formula with these inputs yields: ΔP per 100 ft = 0.2083 × (100/130)^1.852 × 15^1.852 / 0.785^4.865. ≈ 8.4 psi/100 ft. Total for 60 ft = 8.4 × 0.60 = 5.0 psi friction loss. Plus fittings (40 % addition): 5.0 × 1.4 = 7.0 psi total. If supply pressure is 50 psi and fixture needs 8 psi, available after elevation: check before assuming adequate.. This demonstrates a typical pressure drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Applying the Pressure Drop Calc formula with these inputs yields: V = 400 × 0.00223 / (π × 4.026²/576) = 0.892 / 0.0883 = 10.1 ft/s (slightly high — use 6-inch pipe). With 6-inch (ID 6.065 in): V = 0.892/0.2006 = 4.45 ft/s. h per foot = 0.016 × (1/0.505) × 4.45²/64.4 = 0.016 × 1.98 × 0.307 = 0.00973 ft/ft. Total for 400 ft: 3.89 ft of head = 1.68 psi. Well-sized.. This demonstrates a typical pressure drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Applying the Pressure Drop Calc formula with these inputs yields: ΔP = (Q/Cv)² = (10/16)² = 0.391 psi. At 50 % open, Cv drops to ~8: ΔP = (10/8)² = 1.56 psi. Control valve at 50 % open adds 4× more pressure drop than fully open — factor into pump sizing for throttled control scenarios. Size control valves for Cv where normal operating position is 60–70 % open.. This demonstrates a typical pressure drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
Applying the Pressure Drop Calc formula with these inputs yields: Using AGA/IFGC approach: pressure drop tables for 1-inch gas pipe at 50 SCFH over 50 feet ≈ 0.3 psi (low-pressure gas systems ≤ 2 psi supply). Residual = 2.0 − 0.3 = 1.7 psi. Adequate for most residential gas appliances (require minimum 0.5–1.0 psi at appliance). For longer runs or higher flows, upsize to 1.25 inch.. This demonstrates a typical pressure drop scenario where the calculator transforms raw parameters into a meaningful quantitative result for decision-making.
HVAC hydronic system pump selection, representing an important application area for the Pressure Drop Calc in professional and analytical contexts where accurate pressure drop calculations directly support informed decision-making, strategic planning, and performance optimization
Plumbing supply system adequacy check, representing an important application area for the Pressure Drop Calc in professional and analytical contexts where accurate pressure drop calculations directly support informed decision-making, strategic planning, and performance optimization
Natural gas piping design, representing an important application area for the Pressure Drop Calc in professional and analytical contexts where accurate pressure drop calculations directly support informed decision-making, strategic planning, and performance optimization
Industrial process piping, representing an important application area for the Pressure Drop Calc in professional and analytical contexts where accurate pressure drop calculations directly support informed decision-making, strategic planning, and performance optimization
Fire suppression system hydraulic design, representing an important application area for the Pressure Drop Calc in professional and analytical contexts where accurate pressure drop calculations directly support informed decision-making, strategic planning, and performance optimization
In the Pressure Drop Calc, this scenario requires additional caution when interpreting pressure drop results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when pressure drop calculations fall into non-standard territory.
In the Pressure Drop Calc, this scenario requires additional caution when interpreting pressure drop results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when pressure drop calculations fall into non-standard territory.
In the Pressure Drop Calc, this scenario requires additional caution when interpreting pressure drop results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when pressure drop calculations fall into non-standard territory.
| Fitting Type (1 inch) | K Coefficient | Equiv. Length (ft, 1-in pipe) | Resistance |
|---|---|---|---|
| 90° standard elbow | 0.75 | 2.1 ft | Low |
| 90° long-radius elbow | 0.45 | 1.3 ft | Low |
| 45° standard elbow | 0.35 | 1.0 ft | Very low |
| Tee (straight through) | 0.30 | 0.85 ft | Very low |
| Tee (branch flow) | 1.50 | 4.2 ft | Medium |
| Gate valve (fully open) | 0.20 | 0.56 ft | Very low |
| Ball valve (fully open) | 0.05 | 0.14 ft | Negligible |
| Globe valve (fully open) | 10.0 | 28.1 ft | High |
| Swing check valve | 2.0 | 5.6 ft | Medium |
| Reducer (2:1 area ratio) | 0.30 | 0.85 ft | Low |
What is the difference between static and dynamic pressure?
Static pressure: pressure in fluid at rest, caused by fluid weight and supply pressure. Dynamic pressure (velocity pressure): pressure due to fluid motion = ρV²/2. Total pressure = static + dynamic. Pressure drop due to friction converts total pressure energy to heat. Flow meters measure differential pressure to calculate flow rate using the Bernoulli relationship between pressure and velocity.
What is a Cv value for valves?
Cv (flow coefficient) characterizes a valve's flow capacity: Cv = Q / √(ΔP) for water (Q in GPM, ΔP in psi). A valve with Cv = 10 passes 10 GPM with 1 psi pressure drop. Used to select control valves, ball valves, and check valves. Higher Cv = more open/larger valve = less pressure drop. Valves should be selected for the target Cv at the design flow and acceptable pressure drop.
What is head loss in feet vs. psi?
Head loss in feet is a unit-independent way to express pressure drop: 1 psi = 2.31 feet of water head (for water at 60°F). Head loss is commonly used in pump performance curves (which show head in feet vs. flow in GPM). Converting between: psi = feet × SG / 2.31 (where SG = specific gravity; 1.0 for water, higher for glycol antifreeze mixtures).
How do I determine friction factor for different flow regimes?
Laminar flow (Re < 2,300): f = 64/Re. Turbulent flow: use Colebrook-White equation (iterative) or Moody diagram. For fully turbulent rough pipe: f = 1 / (−2 × log₁₀(ε/3.7D))². For most practical pipe flow, commercial pipe roughness tables give friction factors directly. Swamee-Jain explicit approximation avoids iteration: f = 0.25 / (log₁₀(ε/3.7D + 5.74/Re^0.9))².
How do I balance a hydronic heating or cooling system?
System balancing ensures design flow is achieved in every circuit. Steps: (1) size all piping for target velocity and pressure drop; (2) identify the 'index circuit' — the longest/highest pressure drop path; (3) add balancing valves to shorter circuits to add artificial resistance matching the index circuit; (4) set pump for total index circuit pressure drop at design flow. Variable-speed pumps with differential pressure control automatically adjust to load.
Does pressure drop increase with flow rate?
Yes — dramatically. In turbulent flow (most pipes), pressure drop ∝ V² ∝ Q². Doubling flow rate quadruples pressure drop. This is the critical relationship for pump sizing — a pump must supply significantly more head for higher flow rates. Pump curves (head vs. flow) decrease as flow increases, while system curves (required head vs. flow) increase — they intersect at the operating point.
What is allowable pressure drop per foot for hydronic systems?
ASHRAE recommends 1–4 feet of head per 100 feet of pipe for hydronic systems (0.43–1.73 psi/100 ft) as a first sizing criterion, balanced against flow velocity limits (4–12 ft/s for steel, 3–8 ft/s for copper in hydronic systems). The traditional rule of thumb is 2–3 ft/100 ft (0.87–1.30 psi/100 ft) for main headers and risers.
プロのヒント
In hydronic systems, sketch the 'index circuit' (longest pressure drop path from pump supply to return) and calculate pressure drop element by element: each pipe section, each elbow, each tee, each valve, each coil. Then select a pump whose curve intersects the system curve at or slightly above the design flow point.
ご存知でしたか？
The pressure drop formula dates to Henry Darcy (1803–1858), a French engineer who conducted careful experiments on flow through packed sand beds and pipes to understand groundwater and water supply hydraulics. His experimental work also forms the basis of Darcy's Law for groundwater flow through porous media — fundamental to modern hydrology and geotechnical engineering.