Uitgebreide gids binnenkort beschikbaar
We werken aan een uitgebreide educatieve gids voor de Pull System Calculator. Kom binnenkort terug voor stapsgewijze uitleg, formules, praktijkvoorbeelden en deskundige tips.
A pull system is a production and inventory management approach where work is initiated only in response to actual downstream demand — 'pulling' material through the value stream — rather than pushing work based on a production schedule or forecast. A pull system calculator helps operations managers design and size pull systems, including the calculation of pull signals, loop inventory, response time, and the comparison of pull versus push inventory levels. In a push system, production forecasts drive schedules and materials are pushed to downstream processes regardless of actual consumption — creating excess WIP and finished goods inventory. In a pull system, a consumption signal (kanban card, empty bin, electronic trigger, reorder point breach) authorizes upstream replenishment. Pull systems can be implemented as: (1) Kanban — visual cards signal replenishment; (2) CONWIP (Constant Work-in-Process) — a fixed WIP cap limits the total inventory in a production loop; (3) Reorder Point (ROP) — replenishment triggered when inventory drops below a threshold; (4) Demand-Driven MRP (DDMRP) — a modern hybrid that uses strategic buffer positions and demand-driven priority signals. The pull system calculator sizes the inventory loop: maximum WIP authorized = Takt Time × Cycle Time × Safety Factor. It also calculates the response time benefit (pull systems respond to actual demand rather than forecast lag) and the inventory reduction potential versus an equivalent push system.
CONWIP Limit = Target Lead Time / Takt Time (units) Kanban Count (Pull) = (Demand × Lead Time × (1 + Safety Factor)) / Container Size Pull System Response Time = WIP in System / Throughput Rate Push vs. Pull Inventory Savings = (Average Push WIP − Pull WIP Target) × Unit Cost Throughput (Little's Law) = WIP / Lead Time
- 1Determine takt time: available production time / customer demand rate.
- 2Map current WIP at each process step for the push baseline.
- 3Set pull WIP target using CONWIP or kanban method.
- 4Calculate authorized WIP = throughput rate × target lead time.
- 5Design replenishment signals: kanban cards, bins, or DDMRP buffers at strategic decoupling points.
- 6Estimate pull system lead time using Little's Law: LT = WIP / Throughput.
- 7Calculate inventory reduction and working capital savings versus current push system.
CONWIP caps total work-in-process at 600 units regardless of which process steps they're at. When 1 unit ships, 1 release card is authorized to enter the system — maintaining steady state at 600 units WIP.
Converting from push to pull eliminates 82% of WIP inventory, freeing $166K in working capital. Lead time also drops from ~22 days to ~4 days (Little's Law), dramatically improving customer responsiveness.
Little's Law (L = λW) states that average inventory = throughput rate × average time in system. Rearranging: Lead Time = WIP / Throughput. Reducing WIP from 1,200 to 300 units cuts lead time from 4 to 1 day.
DDMRP creates a 3-zone buffer: Red (never let inventory drop below), Yellow (working stock), Green (order cycle buffer). Orders fire when inventory enters Yellow. This decouples demand and supply variability at strategic buffer points.
Lean manufacturing engineers designing kanban or CONWIP pull systems for production lines, representing an important application area for the Pull System Calc in professional and analytical contexts where accurate pull system calculations directly support informed decision-making, strategic planning, and performance optimization
Supply chain planners implementing DDMRP in ERP systems to replace traditional MRP, representing an important application area for the Pull System Calc in professional and analytical contexts where accurate pull system calculations directly support informed decision-making, strategic planning, and performance optimization
Hospital operations teams applying pull to patient flow management, representing an important application area for the Pull System Calc in professional and analytical contexts where accurate pull system calculations directly support informed decision-making, strategic planning, and performance optimization
Software teams applying kanban WIP limits to development and deployment pipelines, representing an important application area for the Pull System Calc in professional and analytical contexts where accurate pull system calculations directly support informed decision-making, strategic planning, and performance optimization
{'case': 'Pull for Service Industries', 'note': 'Pull principles apply beyond manufacturing: hospitals use pull to move patients from the ED to inpatient beds only when beds are available; airlines use pull to gate passengers only when boarding is ready; software teams use kanban boards to limit WIP in development queues.'}
{'case': 'Pull in E-Commerce Fulfillment', 'note': "Amazon's fulfillment network operates as a massive pull system — inventory is replenished from distribution centers to fulfillment centers based on actual sales velocity signals (pull), not forecasts alone. DDMRP-like buffer positions are used at strategic points in the fulfillment network."}. In the Pull System Calc, this scenario requires additional caution when interpreting pull system results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when pull system calculations fall into non-standard territory.
In the Pull System Calc, this scenario requires additional caution when interpreting pull system results. The standard formula may not fully account for all factors present in this edge case, and supplementary analysis or expert consultation may be warranted. Professional best practice involves documenting assumptions, running sensitivity analyses, and cross-referencing results with alternative methods when pull system calculations fall into non-standard territory.
| Pull System Type | WIP Control Method | Best Application | Implementation Complexity |
|---|---|---|---|
| Two-Bin Kanban | Physical bins | Simple, stable demand | Very Low |
| Card Kanban | Kanban cards | Moderate complexity | Low |
| CONWIP | System-wide WIP cap | High-mix, low-volume | Medium |
| Reorder Point (ROP) | Min inventory trigger | Warehousing/distribution | Low |
| DDMRP | Dynamic buffer zones | Complex supply chains | High |
| VMI Pull | Supplier-managed signals | Supplier-customer partnerships | Medium |
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
This is particularly important in the context of pull system calculator calculations, where accuracy directly impacts decision-making. Professionals across multiple industries rely on precise pull system calculator computations to validate assumptions, optimize processes, and ensure compliance with applicable standards. Understanding the underlying methodology helps users interpret results correctly and identify when additional analysis may be warranted.
Pro Tip
Use a Value Stream Map (VSM) to identify your current push vs. pull boundaries before designing a pull system. The VSM will show WIP pile-ups between process steps — these are the decoupling points where kanban or CONWIP signals should be placed to convert from push to pull flow.
Wist je dat?
The Toyota Production System's pull principle was inspired by US supermarkets — specifically Taiichi Ohno's 1956 visit to Piggly Wiggly grocery stores in the US, where he observed shelves being restocked only as items were purchased (pull). He brought this supermarket model back to Toyota and developed the kanban system to replicate it on the factory floor.